Configuring X.25 link through Cisco IP network - Revision history

PoC: /* See also */ +link

2026-02-01T23:51:01Z

PoC: /* Configuration */ remote

2025-11-13T10:22:02Z

Configuration: remote

← Older revision		Revision as of 12:22, 13 November 2025
Line 90:		Line 90:
	\|-		\|-
	\|valign="top"\|'''Line description'''		\|valign="top"\|'''Line description'''
	\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(lin011) lglchle((006 pvc)) netadr(00000000000000) cnninit(~~remote~~) interface(rs232v24) linespeed(19200) dftpktsize(512) modulus(128) adrinsert(no) linkspeed(64000) cmnrcylmt(1 10)</code>		\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(lin011) lglchle((006 pvc)) netadr(00000000000000) cnninit(local) interface(rs232v24) linespeed(19200) dftpktsize(512) modulus(128) adrinsert(no) linkspeed(64000) cmnrcylmt(1 10)</code>
	\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(cmn01) lglchle((005 pvc)) netadr(00000000000000) cnninit(~~remote~~) interface(rs232v24) linespeed(19200) dftpktsize(512) modulus(128) adrinsert(no) linkspeed(64000) cmnrcylmt(1 10)</code>		\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(cmn01) lglchle((005 pvc)) netadr(00000000000000) cnninit(local) interface(rs232v24) linespeed(19200) dftpktsize(512) modulus(128) adrinsert(no) linkspeed(64000) cmnrcylmt(1 10)</code>
	\|-		\|-
	\|valign="top"\|'''Exchange-ID'''		\|valign="top"\|'''Exchange-ID'''

PoC: /* Configuration */ Typos

2025-11-13T09:03:59Z

Configuration: Typos

← Older revision		Revision as of 11:03, 13 November 2025
Line 90:		Line 90:
	\|-		\|-
	\|valign="top"\|'''Line description'''		\|valign="top"\|'''Line description'''
	\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(lin011) lglchle((006 pvc)) netadr(00000000000000) cnninit(remote) interface(rs232v24) linespeed(~~64000~~) dftpktsize(512) modulus(128) adrinsert(no~~) netctl(nibbler~~) linkspeed(64000) cmnrcylmt(1 10)</code>		\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(lin011) lglchle((006 pvc)) netadr(00000000000000) cnninit(remote) interface(rs232v24) linespeed(19200) dftpktsize(512) modulus(128) adrinsert(no) linkspeed(64000) cmnrcylmt(1 10)</code>
	\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(cmn01) lglchle((005 pvc)) netadr(00000000000000) cnninit(remote) interface(rs232v24) linespeed(~~64000~~) dftpktsize(512) modulus(128) adrinsert(no~~) netctl(fiona~~) linkspeed(64000) cmnrcylmt(1 10)</code>		\|valign="top"\|<code>crtlinx25 lind(x25line) rsrcname(cmn01) lglchle((005 pvc)) netadr(00000000000000) cnninit(remote) interface(rs232v24) linespeed(19200) dftpktsize(512) modulus(128) adrinsert(no) linkspeed(64000) cmnrcylmt(1 10)</code>
	\|-		\|-
	\|valign="top"\|'''Exchange-ID'''		\|valign="top"\|'''Exchange-ID'''
Line 98:		Line 98:
	\|-		\|-
	\|valign="top"\|'''Controller description'''		\|valign="top"\|'''Controller description'''
	\|valign="top"\|<code>crtctlappc ctld(nibbler) linktype(x25) line(x25line) maxframe(512) rmtcpname(nibbler) exchid(05641700) netlvl(1984) lglchlid(006) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) ~~cnnrcylmt~~(10 1)</code>		\|valign="top"\|<code>crtctlappc ctld(nibbler) linktype(x25) line(x25line) maxframe(512) rmtcpname(nibbler) exchid(05641700) netlvl(1984) lglchlid(006) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) cmnrcylmt(10 1)</code>
	\|valign="top"\|<code>crtctlappc ctld(fiona) linktype(x25) line(x25line) maxframe(512) rmtcpname(fiona) exchid(05608945) netlvl(1984) lglchlid(005) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) ~~cnnrcylmt~~(10 1)</code>		\|valign="top"\|<code>crtctlappc ctld(fiona) linktype(x25) line(x25line) maxframe(512) rmtcpname(fiona) exchid(05608945) netlvl(1984) lglchlid(005) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) cmnrcylmt(10 1)</code>
	\|}		\|}

PoC: /* Configuration */ typo

2025-11-12T21:05:28Z

Configuration: typo

← Older revision		Revision as of 23:05, 12 November 2025
Line 98:		Line 98:
	\|-		\|-
	\|valign="top"\|'''Controller description'''		\|valign="top"\|'''Controller description'''
	\|valign="top"\|<code>crtctlappc ctld(nibbler) linktype(x25) line(x25line) maxframe(512) rmtcpname(nibbler) exchid(05641700) netlvl(1984) ~~lglchid~~(006) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) cnnrcylmt(10 1)</code>		\|valign="top"\|<code>crtctlappc ctld(nibbler) linktype(x25) line(x25line) maxframe(512) rmtcpname(nibbler) exchid(05641700) netlvl(1984) lglchlid(006) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) cnnrcylmt(10 1)</code>
	\|valign="top"\|<code>crtctlappc ctld(fiona) linktype(x25) line(x25line) maxframe(512) rmtcpname(fiona) exchid(05608945) netlvl(1984) ~~lglchid~~(005) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) cnnrcylmt(10 1)</code>		\|valign="top"\|<code>crtctlappc ctld(fiona) linktype(x25) line(x25line) maxframe(512) rmtcpname(fiona) exchid(05608945) netlvl(1984) lglchlid(005) nodetype(calc) tmsgrpnbr(calc) autodltdev(no) cnnrcylmt(10 1)</code>
	\|}		\|}

PoC: /* Notes */ Error

2025-10-15T13:32:59Z

Notes: Error

← Older revision		Revision as of 15:32, 15 October 2025
Line 106:		Line 106:
	* The PVC-ID for Cisco IOS is a decimal value, and for OS/400, it's a hex value!		* The PVC-ID for Cisco IOS is a decimal value, and for OS/400, it's a hex value!
	* You can use the same PVC on both sides.		* You can use the same PVC on both sides.
			* You cannot create the line description with the full speed outright due to error CPD26DC (Maximum line speed for RS-232/V.24 is 19200 bps.). Create the line with <code>linespeed(19200)</code>, and edit the lind again, setting the desired speed of 64 kbps.

	Proven to work:		Proven to work:

PoC: typo

2025-10-12T20:04:25Z

typo

← Older revision		Revision as of 22:04, 12 October 2025
Line 79:		Line 79:

	interface FastEthernet1/0		interface FastEthernet1/0
	ip address 192.~~1681~~.5 255.255.255.0		ip address 192.168.1.5 255.255.255.0
	\|-		\|-
	!		!

PoC: New

2025-10-12T19:53:57Z

New

New page

Sometimes, older, donated hardware comes without LAN I/O-adapters. Sometimes it has serial communication I/O-adapters, though. This article points out how to network two AS/400's with the help of (older) Cisco hard- and software through the [[wikipedia:X.25|X.25]] protocol, and XOT. This example does not make use of switched virtual circuits (SVC), but permanent virtual circuits (PVC).

== Motivation ==
[[File:Cisco_1005_disassembled.jpg|thumb|right|Cisco 1005, disassembled for de-dusting power connector replacement]]
I wanted my 9401-P03 to be optically present on my desk instead in a dusty corner. The dusty corner had a Cisco 2513 nearby for SDLC network integration, but the new place just has Ethernet. So, another router was needed. Because this machine already generates considerable noise, a fanless router was desired.

First try was with a very old 1005. But even with the latest IOS release 12.0(28d), that model doesn't support SDLC encapsulation on its serial interface. Hence I decided to switch to a common protocol both machines understand: X.25, or Frame Relay. Using ''Frame Relay'' was not feasible, because OS/400 supports Frame Relay only with certain cabling options and IO-Adapters I don't have. Hence I chose X.25 as the last common denominator for RS-232/V.24.

Sadly, the 1005 makes the connection fail as soon as actual transfers are attempted. I tested line speeds down to 9600 bps without success. For fault isolation, I grabbed an old Cisco 1601-R, and copied over the configuration. Connection was working at the first try with 9600 bps. I increased the line speed to 64 Kbps — the same speed the 2612 connected to the other Machine showed was possible without problems. Most notable benefit to use X.25 compared to a direct SLDC link is that serial speeds up to 64 Kbps are allowed and apparently possible, instead of just 19200 bps with SDLC.

== Requirements ==
[[File:IBM 2652.jpg|thumb|right|6152 Adapter, located in a P02]]
[[File:IBM 2609.jpg|thumb|right|2609 Adapter socket, located in a P03]]
[[File:IBM 2609-plugged.jpg|thumb|right|2609 Plug with heavy cable]]
[[File:IBM 2609 Brick.jpg|thumb|right|2609 Breakout-Brick — note that the Cisco cable is plugged directly which is '''wrong''', and only shown for illustration purposes.]]
* Two AS/400 machines, complete and functioning
** <code>QAUTOCFG</code> system variable switched to on
** Local serial port with required breakouts, such as a #2609, #2652, #2720, etc.
** Matching IBM V.24 Modem Cable<ref>If the machine was attached to a modem in earlier times, and you obtained all the cables, all requirements are satisfied.</ref>
<blockquote>'''Note!''' It is of utmost importance to keep in mind that the AS/400 serial ports have ''sense pins'', to know which kind of cable is attached. If you plug in just an ordinary PC serial cable, you’ll eventually find the succinct message in the QSYSOPR message queue, that a cable could not be found. Therefore the requirement of an ''IBM V.24 Modem Cable'', or a self made cable, or adapter, providing the necessary sense pin connectivity.

'''For this reason, you'll need to plug the DB-25F socket connector of the Cisco cable to the modem cable, and not directly to the AS/400’s port.'''</blockquote>

* Cisco 16xx, 26xx or similar router model with T-Type serial interface (card),
** Cisco CAB-232 FC,
** Router LAN ports configured so they can reach each other via IP.

The basic network topology is symmetric. Both AS/400s are connected to their respective Cisco routers through their serial port, and both Cisco routers are connected to each other with some LAN technology, presumably Ethernet.

''Fiona'' → Cisco 1601-R (192.168.1.97) → Cisco 2612 (192.168.1.5) → ''Nibbler''

== Configuration ==
Assumption is that the routers already have a basic configuration applied.

After plugging everything together like pointed out above, obtain the resource names of the serial ports. Type <code>wrkhdwrsc *cmn</code> to get a list of communication hardware, and associated ports. Example:

'''Resource Type Text'''
CMB01 917B Combined function IOP
LIN01 2609 Comm Adapter
LIN011 2609 V.24 Port
LIN012 2609 V.24 Port

<blockquote>'''Note!''' OS/400 V3 seems to not designate ports as ''CMN'', but as ''LIN'' with three digits. Newer releases designate ports on an adapter as ''CMN''.</blockquote>

After you have created the line description, run <code>dsplind x25line</code> to find the generated Exchange-ID.

Here is a table to help configuring what, where, and in which order.

{|class="wikitable"
!Configuration
!Cisco 1601-R (192.168.1.97)
!Cisco 2612 (192.168.1.5)
|-
|valign="top"|'''Cisco IOS'''
|valign="top"|
x25 routing

interface Serial0
description Fiona LIN011
encapsulation x25 dce
x25 modulo 128
x25 ltc 100
x25 pvc 6 xot 192.168.1.5 interface Serial 0/1 pvc 5 packetsize 512 512
clockrate 64000

interface Ethernet0
ip address 192.168.1.97 255.255.255.0
|valign="top"|
x25 routing

interface Serial0/1
description Nibbler CMN01
encapsulation x25 dce
load-interval 60
x25 modulo 128
x25 ltc 100
x25 pvc 5 xot 192.168.1.97 interface Serial 0 pvc 6 packetsize 512 512
clock rate 64000

interface FastEthernet1/0
ip address 192.1681.5 255.255.255.0
|-
! 
!Fiona (V3R2)
!Nibbler (V4R5)
|-
|valign="top"|'''Serial resource'''
|valign="top"|LIN011
|valign="top"|CMN01
|-
|valign="top"|'''Line description'''
|valign="top"|<code>crtlinx25 lind(x25line) rsrcname(lin011) lglchle((006 *pvc)) netadr(00000000000000) cnninit(*remote) interface(*rs232v24) linespeed(64000) dftpktsize(512) modulus(128) adrinsert(*no) netctl(nibbler) linkspeed(64000) cmnrcylmt(1 10)</code>
|valign="top"|<code>crtlinx25 lind(x25line) rsrcname(cmn01) lglchle((005 *pvc)) netadr(00000000000000) cnninit(*remote) interface(*rs232v24) linespeed(64000) dftpktsize(512) modulus(128) adrinsert(*no) netctl(fiona) linkspeed(64000) cmnrcylmt(1 10)</code>
|-
|valign="top"|'''Exchange-ID'''
|valign="top"|05608945
|valign="top"|05641700
|-
|valign="top"|'''Controller description'''
|valign="top"|<code>crtctlappc ctld(nibbler) linktype(*x25) line(x25line) maxframe(512) rmtcpname(nibbler) exchid(05641700) netlvl(1984) lglchid(006) nodetype(*calc) tmsgrpnbr(*calc) autodltdev(*no) cnnrcylmt(10 1)</code>
|valign="top"|<code>crtctlappc ctld(fiona) linktype(*x25) line(x25line) maxframe(512) rmtcpname(fiona) exchid(05608945) netlvl(1984) lglchid(005) nodetype(*calc) tmsgrpnbr(*calc) autodltdev(*no) cnnrcylmt(10 1)</code>
|}

=== Notes ===
* If you change the serial encapsulation value, all X.25 related configuration is discarded!
* The PVC-ID for Cisco IOS is a decimal value, and for OS/400, it's a hex value!
* You can use the same PVC on both sides.

Proven to work:
* Cisco 2612 with added WIC-1T, and image C2600-BINO3S3, Version 12.3(26)
* Cisco 1601-R, and image C1600-BNR2SY, Version 12.3(26)

When one side is powered down, the other side frequently posts error messages to the ''qsysopr'' message queue and problem reporting facility.

== Initiation, and function verification ==
Turn on debugging on the Cisco routers:
term moni
debug x25

Run <code>wrkcfgsts *lin x25line</code> and use the interactive screen to vary on the line on both sides. You should see the lines coming up.
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

On the Cisco Router(s), you should see output of <code>show int ser0/1</code> similar to the following:
Serial0/1 is up, line protocol is up
Hardware is PowerQUICC Serial
Description: Nibbler CMN01
MTU 1500 bytes, BW 19200 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation X25, loopback not set
X.25 DCE, version 1984, address <none>, state R1, modulo 128, timer 0
Defaults: idle VC timeout 0
cisco encapsulation
input/output window sizes 2/2, packet sizes 128/128
Timers: T10 60, T11 180, T12 60, T13 60
Channels: Incoming-only none, Two-way 100-1024, Outgoing-only none
RESTARTs 32/0 CALLs 0+0/0+0/0+0 DIAGs 34/0
LAPB DCE, state CONNECT, modulo 8, k 7, N1 12056, N2 20
T1 3000, T2 0, interface outage (partial T3) 0, T4 0
VS 6, VR 4, tx NR 4, Remote VR 6, Retransmissions 0
Queues: U/S frames 0, I frames 0, unack. 0, reTx 0
IFRAMEs 1664/1953 RNRs 0/0 REJs 0/0 SABM/Es 55/0 FRMRs 0/0 DISCs 0/24
Last input never, output 00:50:34, output hang never
Last clearing of "show interface" counters 23:57:07
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
1 minute input rate 0 bits/sec, 0 packets/sec
1 minute output rate 0 bits/sec, 0 packets/sec
3654 packets input, 76438 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
29 input errors, 0 CRC, 29 frame, 0 overrun, 0 ignored, 0 abort
3526 packets output, 81439 bytes, 0 underruns
0 output errors, 0 collisions, 917 interface resets
0 output buffer failures, 0 output buffers swapped out
51 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

== See also ==
* [[Serial Cables IDs]]
* [[RS-232 Modem Cable Pinout]]
* [[Integrating LAN-less Machines into a local Token Ring]]

* [[Configuring TCP/IP and SLIP with Cisco-Router and V3R2]]

== Weblinks ==
* [https://website.fis.agh.edu.pl/complab/doc/Cisco_IOS_11.0/cbook/cx25.htm Configuring X.25 and LAPB] on Cisco IOS, Faculty of Physics and Applied Computer Science Poland<ref>Very old documentation linked intentionally. Note: The configuration option ''tunnel'' was renamed to ''xot'' in newer IOS releases.</ref>
* [https://public.dhe.ibm.com/systems/power/docs/systemi/v6r1/en_US/sc415405.pdf X.25 Network Support]
* [https://en.wikipedia.org/wiki/RS-232#Timing_signals RS-232 timing signals], Wikipedia
* [https://www.cisco.com/c/en/us/support/docs/routers/10000-series-routers/46800-cab232mtfc.html#cab-232fc Serial Cable CAB-232FC], Cisco.com
* [https://www.ibm.com/resources/publications/OutputPubsDetails?PubID=SY44590203 AS/400 Service Functions], SY44-5902-03<ref>PDF page 245, Table 51, bottom line on that page displays the cable-id connected pins. See also the notes on the top of the next page.</ref>

== Footnotes ==
<references />

[[Category: Hardware Configuration Guide‏]]
[[Category: Software Configuration Guide‏]]

← Older revision		Revision as of 01:51, 2 February 2026
Line 162:		Line 162:
	* [[RS-232 Modem Cable Pinout]]		* [[RS-232 Modem Cable Pinout]]
	* [[Integrating LAN-less Machines into a local Token Ring]]		* [[Integrating LAN-less Machines into a local Token Ring]]

	* [[Configuring TCP/IP and SLIP with Cisco-Router and V3R2]]		* [[Configuring TCP/IP and SLIP with Cisco-Router and V3R2]]
			* [[Serial networking scenarios with Cisco-Routers]]

	== Weblinks ==		== Weblinks ==