View source for Configuring TCP/IP and SLIP with Cisco-Router and V3R2

This article describes how to configure '''OS/400 V3R2''' (and possibly newer) wired to a '''Cisco-Router''' to get '''TCP/IP''' connectivity to the local LAN via SLIP "dialin".

SLIP was a lightweight, but crude protocol. Connection parameters had to be established prior to the communication protocol itself. It was superseded by PPP. OS/400 V3R2 had no PPP support implemented.

This description is based on a proven to work setup.

== Requirements ==
[[File:IBM 2652.jpg|thumb|right|6152 Adapter, located in a P02]]
[[File:Cisco 8P8-Terminal-Adapter.jpg|thumb|right|Adapter from Cisco-Style 8P8 (RJ-45) to DB-25F serial RS-232 connectors]]
* AS/400, complete and functioning
** TCP/IP installed
** Local serial port with required breakouts, such as a #2609, or a #2652
** IBM V.24 Modem Cable<ref>If the machine was attached to a modem in earlier times, and you obtained all the cables, all requirements are satisfied.</ref>
<blockquote>'''Note!''' AS/400 serial ports have ''sense pins'', to know which kind of cable is attached. Therefore the requirement of an ''IBM V.24 Modem Cable'', or a self made cable providing the necessary sense pin connectivity.</blockquote>

* Cisco Router with either 
** an AUX port,
** multiple async lines (like on a 2511),
** a T-Type serial port (built-in or on an add-on card) with platform support to switch that port to async mode.<ref>in interface configuration mode, try to set <code>physical-layer async</code>. If this fails, that particular combination can't handle async over T-Type serial ports.</ref>

Depending on the port used on the Cisco Router, you need a matching cable:
* Cisco CAB-232 FC for a T-Type port,
* Cisco ''Rollover Cable'' — this is a flat 8-wire cable with RJ-45 connectors on each side, but it connects Pin 1 to Pin 8, Pin 2 to Pin 7, and so on. '''Note''': A simple network patch cable will '''not''' work.
* Cisco CAB-500DTF adapter for use with Octopus-Style serial breakout cables for 2511 and similar routers, as well as Cisco Rollover Cables.

In addition, you need to choose an otherwise unused IP address from the LAN the Cisco Router is attached to. We're using 192.168.0.50, while the Ethernet Interface of the Cisco Router has the address 192.168.0.10 255.255.255.0.<ref>We're using Proxy ARP for delivery of the packets over SLIP to the AS/400. Cisco IOS enables this by default.</ref>

The example configuration presented here uses the AUX Port of a Cisco 2513.

== Basic Configuration on AS/400 ==
After plugging everything together like pointed out above, the machine is to be configured. Type ''WRKHDWRSC *CMN'' to get a list of communication hardware, and associated ports. Example:

 '''Resource        Type  Text'''
 CMB01           917B  Combined function IOP
   LIN01         2609  Comm Adapter
     LIN011      2609  V.24 Port
     LIN012      2609  V.24 Port

<blockquote>'''Note!''' OS/400 V3 seems to not designate ports as ''CMN'', but as ''LIN'' with three digits. Newer releases designate ports on an adapter as ''CMN''.</blockquote>

I've connected the AUX-Port of the Cisco to LIN012.

Note that you need the appropriate authority for doing system administration tasks.

We now need to create a ''Line Description'' for this port:
 CRTLINASC LIND(ASYNCLIN) RSRCNAME(LIN012) LINESPEED(19200) TEXT('Serial Line for SLIP') CMNRCYLMT(10 1)

Note that with the tested AS/400 P03, OS/400 V3R2 in combination with a 2609 dual serial port adapter, the maximum serial speed is 19200&thinsp;bps.

== TCP/IP Configuration on AS/400 ==
First, choose a TCP/IP hostname for your machine. The default SNA name comprised of the letter ''S'' followed by the system serial number is sufficient.
* <code>GO CFGTCP</code>
* ''Optional'': Take option <code>20. Configure TCP/IP applications</code>
** take all sub-options, and decide on ''Autostart Server'' to be *YES or *NO. Less servers to start lessens time to start TCP/IP at large. Most often you may want just FTP, and telnet servers to be started automatically.
** Press <code>F12</code>.
* Take option <code>12. Change local domain and host names</code>
** Put in the desired values. If you don't have a DNS domain name, you may use ''local'' as Local domain name.
** Press <code>F12</code>.
* Take option <code>10. Work with TCP/IP host table entries</code><ref>Failing to adhere to this brings up ''failed to find by hostname'' errors in the job logs of the internet servers being started.</ref>
** Enter 1 as ''Opt'' into the first (empty) line, our IP address 192.168.0.50 into the field ''Internet Address'' and press <code>Enter</code>.
** Fill in the host and domain name separated by a dot, for example ''s4412345.local'', and press <code>Enter</code> to save the changes.
** Press <code>F12</code>.
* Take option <code>22. Configure point-to-point TCP/IP</code>, and sub-option <code>1. Work with point-to-point TCP/IP</code>.
** Enter 1 as ''Opt'' into the first (empty) line, type an arbitrary name (such as SLIP0) into the ''Name'' field, and *DIAL into the ''Mode'' field. Press <code>Enter</code> to advance to the details screen.
** Type our IP address 192.168.0.50 into the ''Local interface address'' field
** Type the IP address of the Cisco Router 192.168.0.10 into the ''Remote interface address'' field
** Change ''Add default route'' to Y
** Page down to the next bunch of parameters
** Fill in the name of the line description created above into the field ''Line description''
** Leave all other options at default values, and press <code>Enter</code> twice to save the changes.
** Press <code>F12</code>.
* Type STRTCP, and press <code>Enter</code> to start the TCP/IP stack and servers.

Depending on the machine, this takes some time to complete. '''Note''': A connection attempt will not be made automatically!

== Configuration on the Cisco Router ==
Assumption is that the Router has already a basic configuration applied. This includes the Ethernet Interface.

 aaa new-model
 aaa authentication login serial-lines none
 aaa authorization exec serial-lines none 
 aaa authorization network default local 
 !
 interface Ethernet0
  ip address 192.168.0.10 255.255.255.0
  load-interval 60
  arp timeout 300
 !
 interface Async1
  mtu 576
  ip unnumbered Ethernet0
  encapsulation slip
  load-interval 60
  async default routing
  async mode dedicated
  peer default ip address 192.168.0.50
 !
 ip route 192.168.0.50 255.255.255.255 Async1
 !
 line aux 0
  exec-timeout 0 0
  authorization exec serial-lines
  login authentication serial-lines
  autocommand slip
  stopbits 1
  speed 19200
 !

Notes:
* Be cautious with the AAA-Lines! If you don't have a local user defined, and no enable secret set, you might lock out yourself. Test access with a new telnet connection before closing the existing one!
* The interfaces' name ''Async1'' is hard wired to ''line aux 0''.
* The local route enables proxy ARP to be used on Ethernet 0 for the remote address 192.168.0.50 of the SLIP connection.
* Make sure you actually set ''stopbits 1''. IOS default is 2.

== Starting the connection ==
The SLIP connection is started by means of a batch job being submitted, and running in the background. Unfortunately, the batch job isn't allowed to start the connection by default. You need to change the authority of the connection program once:
 GRTOBJAUT OBJ(QSYS/QTOCPPSM) OBJTYPE(*PGM) USER(QTCP) AUT(*USE)

You can start the connection by either
* Take option <code>1. Work with point-to-point TCP/IP</code>, and type Opt=9 into the line with our created connection profile, or
* from any command line, type <code>STRTCPPTP CFGPRF(SLIP0) OUTPUT(*NONE) AUTODLTCFG(*NO)</code>.

SLIP0 is the connection name created above.

Frequent presses of <code>F5</code> should show that the ''Status'' transitions through different stages until ACTIVE.

== Unresolved issues ==
* ICMP, and UDP (example: SNMP) packets go through quite well. TCP connections hang. ''Tcpdump'' shows that there is no answer from the AS/400 for some time. Example FTP connection attempt from a Linux machine at 192.168.0.11:

 16:11:07.578167 IP 192.168.0.11.50676 > 192.168.0.50.21: Flags [S], seq 3132164903, win 65535, options [mss 1460,sackOK,TS val 3162178493 ecr 0,nop,wscale 2], length 0
 16:11:07.674309 IP 192.168.0.50.21 > 192.168.0.11.50676: Flags [S.], seq 1604102855, ack 3132164904, win 8192, options [mss 536], length 0
 16:11:07.674388 IP 192.168.0.11.50676 > 192.168.0.50.21: Flags [.], ack 1, win 65535, length 0

When the FTP client complains with a timeout error, this is shown.
 16:12:07.674809 IP 192.168.0.11.50676 > 192.168.0.50.21: Flags [F.], seq 1, ack 1, win 65535, length 0
 16:12:07.982822 IP 192.168.0.11.50676 > 192.168.0.50.21: Flags [F.], seq 1, ack 1, win 65535, length 0
 16:12:08.055579 IP 192.168.0.50.21 > 192.168.0.11.50676: Flags [FP.], seq 91, ack 2, win 8192, length 0
 16:12:08.055663 IP 192.168.0.11.50676 > 192.168.0.50.21: Flags [R], seq 3132164905, win 0, length 0

I'm not sure what can be done about that.

== See also ==
* [[Serial Cables IDs]]
* [[RS-232 Modem Cable Pinout]]
* [[Integrating LAN-less Machines into a local Token Ring]]
* [[Post-Install Optimizations#IPL Customization|Post-Install Optimizations]], IPL-Customization, e.&thinsp;g. for automatic start of TCP/IP at IPL time.

== Weblinks ==
* [https://www.cisco.com/c/en/us/support/docs/routers/10000-series-routers/46800-cab232mtfc.html#cab-232fc Serial Cable CAB-232FC], Cisco.com
* [https://ibmdocs.pocnet.net/SY44-5902-03.pdf AS/400 Service Functions], SY44-5902-03<ref>PDF page 245, Table 51, bottom line on that page displays the cable-id connected pins. See also the notes on the top of the next page.</ref>

== Footnotes ==
<references />

[[Category: Hardware Configuration Guide‏]]
[[Category: Software Configuration Guide‏]]